JBL SDP-5 THX Ultra 2 Surround Processor/System Controller

JBL Updated: 2008-09-14 RSS
JBL SDP-5 THX Ultra 2 Surround Processor/System Controller

Audio Input & Output Connectors
Analog Audio Inputs: 8 Stereo (RCA) or 5 stereo and one 5.1-channel or 2 stereo and two 5.1-channel connectors
Digital Audio Inputs
• 4 S/PDIF coaxial (RCA) and 4 S/PDIF optical (TosLink) connectors
• Coaxial and optical input connectors conform to IEC-958, S/PDIF standards
• Accepts 44.1, 48, 88.2 and 96kHz sample rates
• Accepts 16–24 bits PCM audio, Dolby® Digital, DTS® and DTS-ES® discrete data formats
Main Zone Audio Outputs
8 Unbalanced (RCA) connectors for Front L/R, Center, Subwoofer, Side L/R and Rear L/R
Zone 2 Audio Outputs
• 1 Unbalanced (RCA, variable output level) stereo connector
• 1 S/PDIF coaxial (RCA) connector

Main Zone Audio Performance
A/D Conversion: 24-Bit, 96kHz, dual-bit ΔΣ architecture
D/A Conversion: 24-Bit, 44.1 to 192kHz, multi-bit ΔΣ architecture
Frequency Response: 10Hz to 20kHz, +0.05dB/–0.1dB, –0.5dB at 40kHz, reference 1kHz
THD + Noise: Below 0.008% at 1kHz, maximum output level
Dynamic Range: 108dB Minimum, 22kHz bandwidth
Signal-to-Noise Ratio: 108dB Minimum, 22kHz bandwidth
Input Sensitivity: 200mVrms (2Vrms for maximum output level) at 0dB input gain
Input Impedance: 100kΩ in parallel with 150pF
Output Level
• 150mVrms typical, 6Vrms maximum (RCA connectors)
• Maximum value with full-scale input signal and volume at +6dB
Output Impedance
• 100Ω in parallel with 150pF (RCA connectors)
• 50Ω in parallel with 150pF (XLR connectors)

Zone 2 Audio Performance
D/A Conversion: 24-Bit, 44.1 to 192kHz, multi-bit ΔΣ architecture
Frequency Response: 10Hz to 20kHz, +0.1dB/–0.25dB, –0.75dB at 40kHz, reference 1kHz
THD + Noise: Below 0.005% at 1kHz, maximum output level
Dynamic Range: 103dB Minimum, 22kHz bandwidth
Signal-to-Noise Ratio: 103dB Minimum, 22kHz bandwidth
Input Sensitivity: 200mVrms (4Vrms for maximum output level)
Input Impedance: 100kΩ in parallel with 150pF
Output Level
• 200mVrms Typical, 4Vrms maximum (RCA connectors)
• Maximum value with full-scale input signal and volume at 0dB
Output Impedance: 100Ω in parallel with 150pF (RCA connectors)

Video Input & Output Connectors
Video Inputs: 5 Composite (RCA), 5 S-video and 3 component video (RCA)
Video Outputs: 2 Composite (RCA, 1 monitor and 1 Zone 2), 2 S-video (1 monitor and 1 Zone 2) and 1 component (RCA)

Composite & S-video Performance
Compatibility: NTSC, PAL and SECAM
Switching: Active
Output Level: 1.0V Peak-to-peak
Impedance: 75Ω
Input Return Loss: >40dB
Differential Gain: <0.5%
Differential Phase: <0.5°
Bandwidth: >25MHz
K Factor: <0.3%
Gain: ±0.15dB
Signal-to-Noise Ratio: >65dB
Frequency Response: 10Hz to 10MHz, +0.1/–0.3dB

Component Video Performance
Compatibility: 3-Channel (Y, Pr, Pb), format-independent
Switching: Passive
Impedance: 75Ω
Insertion Loss: <3dB
Bandwidth: >150MHz

General
Trigger Outputs: 1 Power on/off and 1 programmable connector on detachable screw terminals (+12VDC, 0.5 amps each)
RS-232 Serial Input/Output: 2 9-Pin D-sub connectors
Power Requirement: 90–250VAC, 50–60Hz, 60W (universal line input), detachable power cord
Unit Dimensions
• Height (with feet): 5.04 inches (128mm)
• Width: 17.3 inches (440mm)
• Depth: 14.85 inches (377mm)
Unit Weight: 24 lb (10.7kg)
Rack Mounting: Brackets are provided for installation in a standard 19-inch equipment rack (3 rack units required)
Environment
• Operating Temperature: 0° to 35°C (32° to 95°F)
• Storage Temperature: –30° to 75°C (–22° to 167°F)
• Relative Humidity: 95% maximum without condensation
Remote Control
• Hand-held, backlit infrared remote control unit
• Requires 2 AA batteries (Alkaline batteries recommended)